555 And Tsop1738 Ir Remote Control Circuits

[Click the image to enlarge it]

Pin Configuration

In the receiver circuit, TSOP1738 receives the IR signal transmitted by IR LED1 of the transmitter circuit. The output of TSOP1738 is fed to transistor T6 through diode D1. The amplified signal is further provided to relay-driver transistor T7. Relay RL1 energises to control the toy car. As jpanhalt have told you already, the TSOP1738 only works properly between 4.5V and 5.5V. Secondly, the output of TSOP1738 cannot source sufficient current to drive a LED as you have connected in your circuit. You can connect a series resistor to the LED, one end of this resistor to +5V and the free end of the LED to the output of the TSOP1738.

TSOP-1738 Characteristics

• Minimum and Maximum Input Voltage is -0.3 and 5V respectively. Typically +5V is used.
• Can detect IR signals from Remotes (38kHz)
• Operating current: 5mA
• High Range and wide coverage area.
• Will respond only to IR signals, due to high immunity against ambient light
• Low power consumption
• Has in-built pre amplifier
• TTL and CMOS compatible

Note: Complete Technical Details can be found at the TSOP1738 datasheet given at the end of this page.

TSOP1738 Equivalent IR Receivers

SM0038, TSOP-17XX

Where to use TSOP-1738 Sensor

The TSOP sensor has the ability to read the output signals from home remotes like TV remote, Home theatre remote, AC remote etc. All these remotes will work with a frequency of 38kHz and this IC can pick up any IR signals process them and provide the output on pin 3. So if you are looking for a sensor to analyse, re-create or duplicate the functions of a remote then this IC will be the perfect choice for you.

Also keep in mind that this series TSOP-1738 will receive only 38Khz IR signals. All remotes in India will operate in 38Khz, kindly ensure if it is the same in your country.

How to test and use TSOP-1738 Sensor

The TSOP-1738 is an IR Receiver Sensor, which can be used to receive IR signals of 38Khz. The sensor operates on 5V and consumes around 5mA to operate. Normally the signal pin (pin 3) IC is connected to a microcontroller to analyse the IR signal received. But let’s consider that you just purchased the IC and you want to check it is working. To do those just connect your TSOP as shown in the test circuit below

Now use any IR remote that’s lying around in your home and press any button on it. You should notice the Green Led blinking each time you press any button. This is just to ensure that the sensor is working as it has to be. Now, you can proceed with any MCU or MPU to decode the received IR signal. Once the IR signal is decoded you can re-create it using an IR Blaster.

TSOP-1738 Applications

• Receive IR signals
• Decode Remote signals
• Analyse, re-create or duplicate remote Signals
• Wireless control applications
• Receiver circuit for IR remote controls
• IR Remote tester circuits

2D model of the component

TSOP1738 is an IR receiver with an amplifier that acts as a switch and converter within a circuit. It has one input and output which only acts on the base of the input IR signal. The basic purpose of TSOP1738 is to convert the IR signal to electric signals. Every IR receiver has a special frequency to operate. TSOP1738 operates on 38KHz IR frequency. In case of higher or lower frequency, it may act due to a current leakage or some other errors but it won’t fully operate. It uses silicon-based technology, which works at the microlevel and very sensitive and efficient to its functions. In summary, TSOP may be smaller in size but its usage with microcontroller and microprocessors makes it smart and secure.

TSOP1738 Pinout diagram

TSOP1738 is just an IR receiver which acts as a switch. It has only three pins that connect TSOP with other devices and make it useful for wireless communication.

TSOP1738 Pin Configuration

We can find it with a metallic head also. As shown in the figure below:

Pinout Description

GND: The ground pin is only to make common ground with other devices, especially microcontrollers and ICs.

VSS: It is a power input pin for activating the internal decoder and IR receiver. The power should be according to its specification and should be only at power pin. In case of power input on any pin even if its low the IC will start heat up which can be noticed by touching it. In the end, heating will damage the TSOP.

Output: The data will come out in the form of the pulse from the output pin. The output pin can be interfaced with any TTL/CMOS devices with a little resistance. Output data will be in voltage form, from the TSOP.

TSOP1738 IR Receiver Features

• It gives the IR receiver and amplifier within a single package.
• Special frequency level makes it operate with a specific device.
• TSOP1738 has an internal bandpass filter to avoid any ambient light especially sunlight.
• The internal filter gives PCM frequency for analog signals
• It is usable with any kind of TTL/CMOS microcontroller, IC or microprocessors.
• Even there are multiple features in a single package the IC still, has low power consumption and the power consumption only happens when it is operating. At stand by position, the power consumption becomes lower.
• TSOP1738 can transfer 1200bits/s and can receive it at the same speed.
• It is an active low output device.

Specifications

• The operating voltage and current for TSOP is -0.3 to 6.0 V and 5mA current.
• The output voltage and current will always be according to the power input.
• The internal junction temperate range is 100 ⁰C.
• TSOP1738 can operate at -25 to 85 ⁰C but it can also store that temperate.
• Its power consumption is 50mW at a maximum temperature which is 85 ⁰C.
• During soldering the IC always keeps the temperature low than 260 ⁰C near its pins otherwise it will burn with external temperature during soldering.

How does the IR receiver work?

The given image is a general block diagram of the internal components of TSOP1738. The detail of every component is discussed below:

TSOP1738 Block Diagram

AGC

As from the block diagram the internal components can be seen clearly but here the use of each component is a reason. IR receiver can work directly but in TSOP other components makes it smart and secure. The IR is first connected to the AGC (Automatic Gain Control). AGC amplifies the input of different types of input signals from the IR receiver. The AGC then passes the output towards the Bandpass filter.

Band Pass Filter

Bandpass filter has multiple roles in TSOP. It first converts the incoming analog signals to digital output levels which then pass towards the demodulator. The combination of AGC and bandpass also makes it avoid any ambient light especially the sunlight because it is common and can be found anywhere easily. The device may have internal sunlight protection but still, the company recommends it to use at a shorter distance. The change in weather may sometimes affect the sunlight which can affect the transmission with TSOP. The bandpass filter also makes the IC operate only at a special frequency which is 38KHz.

Demodulator

The demodulator is connected to the NPN transistor from one end and to Band Pass Filter from the other end. The output data from the bandpass filter will be entered in the demodulator which will drive the NPN transistor using low input signals. NPN transistor is directly connected to the power and output from the collector and with the ground from the emitter side. Every low signal will turn off the NPN transistor and power will be pass towards the output pin.

Control Circuit

The control circuit act as a switch for demodulator and band filter. It generates the output signal whenever the bandpass filter generates the output, the control circuit generates the output signal which tells the demodulator and AGC about completion of filtration.

TSOP1738 IR Receiver Applications

• TSOP1738 may be smaller in size but most of the modern products connect with TSOP1738 internally. Like TV, AC, Doors, etc.
• Security systems like object detection use it with the IR transmitter.
• TSOP1738 use in Line following robots to achieve its goal.
• Hear Beat sensor can be built by using TSOP1738.
• Most of the modern security systems in IoT comes with TSOP1738 with different kinds of applications.
• It is one of the best receivers for a small distance communication but it is only for one-way communication.

TSOP1738 Example Circuits

There are a bunch of TSOP1738 applications but every application uses the same method and circuit. Especially at the commercial level, the TSOP1738 use to make wireless communication to avoid any kind of interaction between humans and machines due to many issues, mostly safety.

Controlling LED with IR remote

In this example, TSOP will be used as a remote tester. In most of the local shops, they have a remote tester that has TSOP1738 within itself, which helps to read the incoming signal.

The basic purpose of this device is to view the incoming signal from the remote. The signal coming from remote is unable to see with the naked eye. The following circuit helps the vendors to view the remote signals in the form of light.

TSOP1738 Example

In this circuit, TSOP1738 operates an LED by using transistors and some resistors. The output of the TSOP connects with the base of the NPN transistor and the transistor controls the LED. Whenever the remote button will press in front of the TSOP1738 the LED will start blinking. The blink of LED will be according to the incoming signal and can be viewed by the human eye easily.

Controlling LED with Arduino

In this example, we learn to control the LED with Arduino. This diagram shows an IR receiver interfacing with Arduino.

For working and code check this complete article and video:

Projects Examples

These are the projects based on TSOO1738.

Security issues with TSOP1738

The decoding speed of TSOP makes it smarter. In most of the devices, TSOP1738 connects with microcontrollers. In a microcontroller, there are a bunch of methods by which the microcontroller will act on the incoming signal. The receiver can transfer the data up to 1200bit/sec. In the controller, the incoming data can be defined for different events. The larger number of data is hard for anyone to guess and there is no way to bypass the TSOP directly.

Many generate able data may help to make the device secure but there’s a flaw in this system too. Whenever the transmitter sends the data, it doesn’t have any restrictions for the receiver end. Any device with TSOP1738 can receive the data. TSOP1738 doesn’t have any smart detection method of neglecting the incoming signal. The only basic function of TSOP is to generate the incoming IR signal to the electrical signals. This is the reason every remote can be reverse-engineered by using Microcontroller with TSOP1738. This issue doesn’t affect much because IR transmission only uses in short transmission devices.

2D Diagram